ARAŞTIRMA
METAL DESTEKLİ DENTAL SERAMİKLERDE FARKLI YÜZEY HAZIRLAMA İŞLEMLERİNİN GLAZÜR TABAKASI VE SERAMİK RENGİNE ETKİSİNİN DEĞERLENDİRİLMESİ
Niler Özdemir Akkuş, Rahime Tüzünsoy Aktaş, M. Heval Şahan
ÖZET
Amaç: Bu çalışmada seramik restorasyonlarda glaze öncesi farklı yüzey hazırlama yöntemlerinin naturel glazür (yüksek ısı glazürü) ve over glazür (düşük ısı glazürü) sonrası seramik rengine etkisinin karşılaştırılması amaçlanmıştır.
Materyal ve Metod: Çalışmamız için 1 cm çapında 1,5 mm kalınlığında toplam 50 adet disk şekilli, metal alt yapı (Remanium CS, Dentaurum, Pfrozheim, Germany) hazırlanmıştır. Metal alt yapılar üzerine son kalınlığı 3 mm olacak şekilde özel kalıp üzerinde A2 dentin seramiği (Ceramco II, Ceramco Inc., State, USA) uygulanmıştır. Örnekler 5 gruba ayrılarak her bir gruba elmas frez, elmas frez+taş, elmas frez+taş+lastik, elmas frez+taş+zımparalama ve elmas frez+taş+kumlama şeklinde yüzey bitirme işlemleri uygulanmıştır. Daha sonra örnekler 2 alt gruba ayrılmış ve yüzeylere natural glazür ve over glazür uygulanmıştır (n=5). Yüzey pürüzlülük değerleri (Ra) glazür öncesi ve sonrasında Atomik Kuvvet Mikroskobu ile ölçülmüş ve kaydedilmiştir. Renk ölçümleri yine glazür öncesi ve sonrasında spektrofotometre ile ölçülmüş ve ∆E değerleri hesaplanmıştır. Tüm veriler “tek yönlü varyans analizi (ANOVA) ile p=0,05’lik önem seviyesinde incelenmiştir. Varyans homojenliği olan natural glaze grubunda “Bonferroni testi”, varyans homojenliği olmayan over glaze grubunda ise “Dunnet C” testi ile grupların ikili analizi yapılmıştır.
Bulgular ve Sonuç: Over glaze uygulanan örneklerde farklı yüzey hazırlama teknikleri ile elde edilen renk değerleri arasında anlamlı bir farklılık olmadığı saptanmıştır. Ancak naturel glazür uygulanmış örneklerde yüzey hazırlama yöntemlerinin rengi anlamlı derecede etkilediği görülmüştür (p<0,05).
Anahtar Kelimeler: Dental seramikler, atomik kuvvet mikroskobu, renk, glazür. Nobel Med 2020; 16(1): 63-69
EVALUATION OF THE EFFECT OF DIFFERENT SURFACE PREPARATION PROCEDURES ON GLAZE LAYER AND THE SHADE OF METAL SUPPORTED DENTAL CERAMICS
ABSTRACT
Objective: The aim of this study was to compare the effect of different surface preparation methods on color both in natural glaze (high temperature glaze) and over glaze (low temperature glaze) in ceramic restorations.
Material and Method: For this study, 50 disc shaped, metal substructures (Remanium CS, Dentaurum, Pfrozheim, Germany) with a diameter of 1 cm and a thickness of 1.5 mm were prepared. A2 dentin ceramic (Ceramco II, Ceramco Inc., State, USA) was applied on metal substructures in a special mold with a final thickness of 3 mm. Specimen were divided into 5 groups and diamond bur, diamond bur+stone, diamond bur+stone+rubber, diamond bur+stone+sand paper and diamond bur+stone+sandblasting surface preparation methods were applied to all samples. Then, each group were divided into two subgroups and natural glaze and over glaze were applied (n=5). Surface roughness values (Ra) were measured and recorded by Atomic Force Microscope before and after glazing. Color measurements were also conducted by spectrophotometer before and after glazing and ∆E values were calculated. All data were analyzed with one way ANOVA (p=0.05). In the natural glaze group with variance homogeneity, Bonferroni test and in the over glaze group without variance homogeneity, Dunnet C test was used to analyze the groups.
Results and Conclusion: It was determined that there was no significant difference between the color values obtained by using different surface preparation methods in over glaze group. It was observed that surface preparation methods had a significant effect on color in natural glaze group (p<0.05).
Keywords: Dental ceramics, atomic force microscope, color, glaze. Nobel Med 2020; 16(1): 63-69
Makalenin PDF formatındaki tam metin versiyonu için buraya tıklayınız.